gur_helios ✭✭✭

Hello everyone I just got build 27.0.46.231. A restart of the system after installing the update was not required. Regards Uwe

Hello everyone I just got build 27.0.45.220.😊 A restart of the system after installing the update was not required. Regards Uwe

Hi everyone I just got build 27.0.44.217.😊 A restart of the system after installing the update was not required. Regards Uwe

@Alexandru_BD Yep... almost flegged, but still squab. 😅 And thank you. Anytime again. 😀

Hi everyone I just got build 27.0.42.214.😀 A restart of the system was not required. There is no changelog available yet at the time of writing this post. Regards, Uwe

Thank you very much for providing the detailed changelog, Alex! 😊 Greetings, Uwe

Hi everyone I just got build 27.0.42.210.😀 A restart of the system was not required. Regards, Uwe

Hi everyone I just got build 27.0.41.208.😀 A restart of the system was not required. There is no changelog available yet at the time of writing this post. Kind regards, Uwe

Hi everyone I got the new build 27.0.41.201 also this morning. A restart of the system was not required, but the installation process took some time. Thus, have a cup of java and lie back till the update process is done. 😉 Kind regards, Uwe

Hi everyone I just got build 27.0.41.197. A restart of the system was not required. There is no changelog available yet at the time of writing this post. Kind regards, Uwe

Hi everyone I just got the new build 27.0.41.194. A restart of the system was not required, but the installation process took some minutes to get finished. Regards, Uwe

Hi everyone I just got the new build 27.0.40.173. A restart of the system was not required. There is no changelog available yet at the time of writing this post.

Just got the new build. A restart was not necessary.

Hi friends I got build 27.0.38.163 two hours ago. A device restart was not necessary to take the changes in effect, but it took a while until the update was installed. Thus, be patient and don't stop the update process until it runs completely through. Regards, Uwe

Same here 😁 In the release notes, build 27.0.35.146 is still mentioned, but the update came with build 27.0.35.147. 😊 @Gjoksi I just see that the my scan engine is a little bit newer than yours. Engine version 7.96555 to 7.96553. Initiate an update again and check the scan engine version afterwards. Regards, Uwe Addendum:…

Hi friends I just got build 27.0.30.140 which fixes the "Autoscan" issue at boot up. A device restart was not necessary to take the changes in effect. Regards

Hi, I'm pretty sure your autoscan settings are set back to the default values if you make a reboot. Did you try that out? https://community.bitdefender.com/en/discussion/comment/335055/#Comment_335055 Regards

Hi folks My experience with the latest build 27.0.30.136 of Bitdefender is that the autoscan settings are reset to the following values every time. See screenshot below. However, the settings should remain with the previously selected changes after restarting the system as can be seen below. The same error already occurred…

Hello together I just got the latest build 27.0.30.135 of Bitdefender introducing a "Cryptomining Protection" module. I system restart was required for the changes to take effect. Regards

Hi folks Thank you very much for your profound explanations. It's all clear now. 😊 And good to hear that. 🥳 Greetings Uwe 🤗

Hello together I just got the latest build of Bitdefender. A restart was not required. Following question. When Bitdefender is updated without a required restart, is the system vulnerable (for some seconds) while updating the new files? Wouldn't it be better if a restart was always required to avoid preceding scenario?…

Hi everyone I just got Bitdefender version 27.0.25.116. 😀 A restart was NOT required to install the new version. Best wishes, Uwe 🤗

Hello everyone Short feedback. Hurray... the file wingetui.exe is not flagged as a generic virus anymore. 🤗 Best wishes, Uwe

Thanks for the explanation. My database is always up-to-date 'cause it is updated hourly. I will check the file tomorrow with the latest malware database again if anything has already changed. Alright, it's time for me to go to bed. Was a long day. Wishing you also a good night. Till then, Uwe 😴

I've just submitted the file and the source of it again, but this time I got an email feedback saying that it can take up to the usual 72 hours to analyze the file and update the malware database. 😉 Somehow strange... I didn't get a feedback by email last Friday. 😏 So, let's abide if something's gonna change. I'm in good…

@Flexx I already submitted the file and the link of its orgin last Friday, but I haven't got an answer or something like that by now. I will try out later if the malware database has been updated and the file is not flagged as a malware anymore 'cause Virustotal also says it's not a malware. Greetings, Uwe PS: A system…

Yes, the malware database is up-to-date (as usual). And yes I know, on Virustotal, the file is not recognized as a malware. I checked this first last week. But Bitdefender (local app) still flags WingetUI.exe as a generic virus as you see below. I've created an expection for the file. By the way... WingetUI 2.1.1 is not…

Hello everyone I submitted a file last Friday which Bitdefender recognized as a false positive. The 72 hour response time has now passed and Bitdefender still recognizes the file as a false positive. The file is called WingetUI.exe and can be found under the following link (in the packed file version 2.1.2 beta 1):…

Hi guys I got the update this noon (CET). A device restart was required to activate the changes.

Many thanks for the clarification, Alex. :-)